Servo I Ventilator Operator Manual
Servo I ventilator Experitory block. I have need Servo I ventilator Experitory block. MAQUET SERVO-i Compressor Mini Service Manual MAQUET SERVO-i. EBooks Servo I Ventilator User Manual are currently available in various formats such as PDF, DOC and ePUB which you can directly download and save.
Servo i service manual. 1. Servo-i Ventilator SystemService Manual CRITICAL CARE.
Servo-i Ventilator System ImportantNotes1-2 Service Manual Revision 02. Important Servo-i Ventilator SystemContents1. Description of functions. Disassembling and assembling. Service procedures. Preventive maintenance.
9Revision 02 Service Manual 1-3. Servo-i Ventilator System Important Important General Symbols used in this manual. Service documentation for the Servo-i Ventilator. ESD sensitive components. When1 System consists of: handling ESD-sensitive devices, established procedures must be – Users manual. The Users manual is an observed to prevent damage. Indispensable complement to the Service Manual for proper servicing.
Special waste. Discard disposable, – Service Manual replaced and left-over parts in – Installation Instructions accordance with appropriate industrial and environmental – Spare Parts information. – Documentation for all optional equipment included in the Servo-i System is also available.
Recycle if possible. The Servo-i Ventilator System is referred to as Recycling facilities may not be the Servo-i troughout this manual.
Available in all areas. There are two serial number labels on the unit:. Technical training. Refers to the – One label is attached to the Patient Unit close Technical training supplied by to the supply gas inlets.
The serial number Maquet. Stated on this label is the ID number of the Patient Unit. The serial number is also stored in the SW memory as the System ID.
Service contract. Refers to the – One label is attached to the rear side of the Service contract supplied by User Interface close to the On/Off switch. Serial number stated on this label is the ID number of the User Interface. Randall knight physics.
System version number can be found in the Status window on the User Interface. Make sure Hazard notices that the version of the Users manual. Before disassembling or assembling of the corresponds to the System version. Servo-i, make sure that the: – On/Off switch is set to Off. Text inside a box is used to highlight important – Mains power cable is disconnected.
– Gas supply is disconnected (wall and/or cylinder). In addition to the Important information given – Battery modules are disconnected. Here and in the related documents (e.
Maquet Servo I Ventilator Manual
In the Users manual), always pay attention to – The Servo-i is cleaned according to applicable local and national regulations. Instructions in the Users manual, chapter Routine cleaning and chapter Regular. Responsibility for the safe functioning of the maintenance, section Extended cleaning of equipment reverts to the owner or user in all inspiratory channel. Cases in which service or repair has been done by a non-professional or by persons who are not. With power supply connected to the Servo-i, employed by or authorized by Maquet, and when there are energized electrical components inside the equipment is used for other than its intended the unit. All personnel must exercise extreme purpose.
Caution if fault tracing or adjustments are performed with power supply connected and with user interface and patient unit covers removed. 1-4 Service Manual Revision 02. Important Servo-i Ventilator System Important Installation To the responsible service personnel.
Only personnel trained and authorized. The contents of this document are not binding. By Maquet shall be permitted to install the Servo-i. The installation and If any significant difference is found between the product and this document, please contact 1 handing over procedures are described Maquet for further information.
In the Servo-i Ventilator System –. We reserve the right to modify products without Installation Instructions. Amending this document or advising the user. Only personnel trained and authorized Functional check by Maquet shall be permitted to perform installation, service or. After any installation, maintenance or service maintenance of the Servo-i. Intervention in the Servo-i, perform a Pre-use Only Maquet genuine spare parts must check according to instructions in the Servo-i be used.
PC boards (spare parts) must always be Ventilator System – Users manual. Kept in a package for sensitive electronic devices. Maquet will not otherwise assume responsibility for the materials used, the work Service performed or any possible consequences of. The Servo-i must be serviced at regular same. Intervals by personnel trained and. The device complies to standards and authorized by Maquet.
Requirements as stated in the Servo-i Ventilator Any maintenance or service must be System – Users manual. Noted in a log book provided. It is recommended that maintenance and service is done as a part of a service contract with Maquet. Preventive maintenance must be performed at least once every year as long as the unit is not used more than normal.
Normal operation is estimated to correspond to approx. 5.000 hours of operation. Details are found in this Service Manual, chapter ”Preventive maintenance”. The Battery modules shall be replaced every three years. The internal Lithium batteries (on PC 1771 and PC 1772) shall be replaced every five years.
Worn-out batteries must be recycled or disposed of properly according to local regulations. Recycle facilities may not be available in all areas. Batteries must not be disposed of with ordinary waste. Discard all other disposable, replaced and left-over parts in accordance with appropriate industrial and environmental standards. When working with ESD sensitive components, always use a grounded wrist band and a grounded work surface. Adequate service tools must always be used.Revision 02 Service Manual 1-5. Servo-i Ventilator System Important Important Environmental declaration Purpose Construction materials1 This environmental declaration is for a Servo-i The construction materials used in Servo-i in% of basic unit including the carrier and one battery.
The total weight. Letters codes within brackets refers to the Functional Block Diagram in chapter Diagrams. Metal – total 77%.
Aluminium 70% Components with special environmental concern. Steel, zink, brass 8% Components listed below shall be disposed of in an environmentally safe way.